This Aussie Traveller Light Bar 4WD 41.5" LED throws serious punch straight down the track so you can spot washouts and stock before you are on them. The bar length around 105 cm suits most bullbars and flat racks without crowding other gear. The housing depth near 8 cm keeps it tucked in tight so branches and scrub do not grab it on narrow bush tracks. The body runs an aluminium extrusion roughly 60 mm high and 80 mm deep so the LEDs stay cooler on long night sections. A clear polycarbonate lens covers the full 41.5" front face to shrug off stones on gravel roads. Side brackets in about 4 mm steel bolt straight to common M8 points on bars and racks. The bar ties into a standard 12 V setup which suits most touring wagons and dual cabs across Australia.
- 41.5 inch LED light bar length
- Approximate 105 cm total bar span
- Slim housing about 60 mm high
- Housing depth roughly 80 mm front to back
- Aluminium body for strength and heat control
- Clear polycarbonate lens across full face
- Side-mount brackets in about 4 mm steel
- Brackets suit common M8 mounting points
- Compatible with standard 12 V 4WD systems
- Ideal for bullbar or roof rack mounting
Q: Can this 41.5" LED light bar run on a standard 12 V 4WD electrical system?
Yes, this light bar is built for 12 V setups. Most touring wagons and dual cabs in Australia use a 12 V system from the factory, so the bar ties in with typical relay and switch looms. A dedicated fused circuit still makes sense for reliability. An auto sparky or competent DIYer can integrate it into an auxiliary lighting circuit.
Q: Will the 41.5" length fit across a typical 4WD bullbar or flat roof rack?
The bar length is about 105 cm which suits most bullbars and roof racks. Many standard racks sit near 120 cm wide so this bar leaves a bit of space each side for clamps or extra gear. On a bullbar, the width usually matches the vehicle front so the bar sits neatly between uprights. Always double-check your mounting span before drilling.
Q: What materials are used in the housing and lens on this light bar?
The bar uses an aluminium housing with a clear polycarbonate lens. Aluminium keeps the weight down while helping move heat away from the LEDs across the 60 mm high and 80 mm deep body. Polycarbonate is chosen for impact resistance when stones flick up on gravel roads. These materials suit long-term touring use across changing Aussie weather.
Q: How is the light bar mounted onto the vehicle?
The bar uses side brackets that bolt through common M8 mounting points. Each bracket foot is about 4 mm thick steel to hold the bar steady over corrugations and rough tracks. You can clamp these to bullbar tabs, rack channels or custom plates. Using stainless hardware and nyloc nuts helps keep the setup tight over time.
- 41.5" light bar for big spread
- Aluminium body helps shed heat
- Tough polycarbonate lens for gravel
- Compact 8 cm depth clears racks
- Side brackets bolt to M8 points
| SKU | 264202003 |
|---|---|
| Barcode # | OEBC562617 |
| Brand | Aussie Traveller |
| Shipping Weight | 12.0000kg |
More info
This Aussie Traveller Light Bar 4WD 41.5" LED throws serious punch straight down the track so you can spot washouts and stock before you are on them. The bar length around 105 cm suits most bullbars and flat racks without crowding other gear. The housing depth near 8 cm keeps it tucked in tight so branches and scrub do not grab it on narrow bush tracks. The body runs an aluminium extrusion roughly 60 mm high and 80 mm deep so the LEDs stay cooler on long night sections. A clear polycarbonate lens covers the full 41.5" front face to shrug off stones on gravel roads. Side brackets in about 4 mm steel bolt straight to common M8 points on bars and racks. The bar ties into a standard 12 V setup which suits most touring wagons and dual cabs across Australia.
- 41.5 inch LED light bar length
- Approximate 105 cm total bar span
- Slim housing about 60 mm high
- Housing depth roughly 80 mm front to back
- Aluminium body for strength and heat control
- Clear polycarbonate lens across full face
- Side-mount brackets in about 4 mm steel
- Brackets suit common M8 mounting points
- Compatible with standard 12 V 4WD systems
- Ideal for bullbar or roof rack mounting
Q: Can this 41.5" LED light bar run on a standard 12 V 4WD electrical system?
Yes, this light bar is built for 12 V setups. Most touring wagons and dual cabs in Australia use a 12 V system from the factory, so the bar ties in with typical relay and switch looms. A dedicated fused circuit still makes sense for reliability. An auto sparky or competent DIYer can integrate it into an auxiliary lighting circuit.
Q: Will the 41.5" length fit across a typical 4WD bullbar or flat roof rack?
The bar length is about 105 cm which suits most bullbars and roof racks. Many standard racks sit near 120 cm wide so this bar leaves a bit of space each side for clamps or extra gear. On a bullbar, the width usually matches the vehicle front so the bar sits neatly between uprights. Always double-check your mounting span before drilling.
Q: What materials are used in the housing and lens on this light bar?
The bar uses an aluminium housing with a clear polycarbonate lens. Aluminium keeps the weight down while helping move heat away from the LEDs across the 60 mm high and 80 mm deep body. Polycarbonate is chosen for impact resistance when stones flick up on gravel roads. These materials suit long-term touring use across changing Aussie weather.
Q: How is the light bar mounted onto the vehicle?
The bar uses side brackets that bolt through common M8 mounting points. Each bracket foot is about 4 mm thick steel to hold the bar steady over corrugations and rough tracks. You can clamp these to bullbar tabs, rack channels or custom plates. Using stainless hardware and nyloc nuts helps keep the setup tight over time.
- 41.5" light bar for big spread
- Aluminium body helps shed heat
- Tough polycarbonate lens for gravel
- Compact 8 cm depth clears racks
- Side brackets bolt to M8 points
| SKU | 264202003 |
|---|---|
| Barcode # | OEBC562617 |
| Brand | Aussie Traveller |
| Shipping Weight | 12.0000kg |
