The Seahorse Tackle Yabby Pump Washer Set steps in when your pump starts to lose pull after a few seasons on the sand flats. This kit drops straight onto a standard pump shaft around 10–12 mm thick and gets the stroke sealing again across a face close to 40–60 mm wide. You keep dragging sand from depths of about 0.1–0.5 m without needing to drag a whole new pump to the beach.
The setup uses paired metal discs and a fibre washer around 2–4 mm thick to clamp tight on the pump head over a travel of roughly 400–600 mm. The metal spreads load so the fibre face wears evenly across many weekends in water between 5–35°C. That mix suits salty Aussie creeks and estuaries where gear cops repeated wet and dry cycles and still has to keep working.
- Complete washer set for yabby pumps
- Includes replacement sealing disc and plates
- Helps restore suction on worn pump heads
- Suitable for typical bait-collecting sand pumps
- Compact flat parts for easy tackle-box storage
- Practical spare kit for estuary and beach trips
- Simple design allows straightforward home fitting
- Cost-effective way to extend pump service life
Q: Is this washer set suitable as a general replacement for most standard yabby pumps?
Yes, it is intended as a general replacement set for typical yabby pumps. The kit gives you the key washer components in one pack so you can refresh a worn head without chasing loose parts. For the best result match the centre hole and disc size to your existing hardware. If they line up well the kit will usually fit and function as expected.
Q: How often should I replace the washers on a yabby pump?
Replace the washers whenever suction noticeably drops or the sealing face looks torn or compressed. Sand and grit slowly wear the surfaces down over repeated sessions. Heavy users who pump most weekends may change washers several times a year. Occasional users might only need a new set every season or two depending on care and storage.
Q: Can I carry this washer set as a spare on longer trips?
Yes, the set is compact and suited to carrying as a spare. Keeping a pack in the tackle bag means a failed washer will not end a bait mission. The flat parts take up very little room and weigh little. That makes them practical backup gear when you are travelling away from local tackle shops.
Q: Do I need special tools to fit this washer set?
No, basic hand tools normally used on a yabby pump will handle the job. Most pumps break down with a simple spanner or by loosening a wing nut. Once opened you just swap the old washers for the new ones and reassemble. The straightforward layout keeps maintenance doable at home or at camp.
- Full washer kit in one pack
- Helps keep yabby pumps working
- Solid spare for coastal trips
- Smart buy for regular bait runs
- Compact setup fits small tackle bags
Complete washer set for yabby pump.
| SKU | YPWSET |
|---|---|
| Barcode # | 9314048104479 |
| Brand | Seahorse Tackle |
| Shipping Weight | 0.2000kg |
More info
The Seahorse Tackle Yabby Pump Washer Set steps in when your pump starts to lose pull after a few seasons on the sand flats. This kit drops straight onto a standard pump shaft around 10–12 mm thick and gets the stroke sealing again across a face close to 40–60 mm wide. You keep dragging sand from depths of about 0.1–0.5 m without needing to drag a whole new pump to the beach.
The setup uses paired metal discs and a fibre washer around 2–4 mm thick to clamp tight on the pump head over a travel of roughly 400–600 mm. The metal spreads load so the fibre face wears evenly across many weekends in water between 5–35°C. That mix suits salty Aussie creeks and estuaries where gear cops repeated wet and dry cycles and still has to keep working.
- Complete washer set for yabby pumps
- Includes replacement sealing disc and plates
- Helps restore suction on worn pump heads
- Suitable for typical bait-collecting sand pumps
- Compact flat parts for easy tackle-box storage
- Practical spare kit for estuary and beach trips
- Simple design allows straightforward home fitting
- Cost-effective way to extend pump service life
Q: Is this washer set suitable as a general replacement for most standard yabby pumps?
Yes, it is intended as a general replacement set for typical yabby pumps. The kit gives you the key washer components in one pack so you can refresh a worn head without chasing loose parts. For the best result match the centre hole and disc size to your existing hardware. If they line up well the kit will usually fit and function as expected.
Q: How often should I replace the washers on a yabby pump?
Replace the washers whenever suction noticeably drops or the sealing face looks torn or compressed. Sand and grit slowly wear the surfaces down over repeated sessions. Heavy users who pump most weekends may change washers several times a year. Occasional users might only need a new set every season or two depending on care and storage.
Q: Can I carry this washer set as a spare on longer trips?
Yes, the set is compact and suited to carrying as a spare. Keeping a pack in the tackle bag means a failed washer will not end a bait mission. The flat parts take up very little room and weigh little. That makes them practical backup gear when you are travelling away from local tackle shops.
Q: Do I need special tools to fit this washer set?
No, basic hand tools normally used on a yabby pump will handle the job. Most pumps break down with a simple spanner or by loosening a wing nut. Once opened you just swap the old washers for the new ones and reassemble. The straightforward layout keeps maintenance doable at home or at camp.
- Full washer kit in one pack
- Helps keep yabby pumps working
- Solid spare for coastal trips
- Smart buy for regular bait runs
- Compact setup fits small tackle bags
Complete washer set for yabby pump.
| SKU | YPWSET |
|---|---|
| Barcode # | 9314048104479 |
| Brand | Seahorse Tackle |
| Shipping Weight | 0.2000kg |
