The RWB Marine Sink Waste & Plug 90Degree 25mm pushes water through a tight 90 degree outlet so you can run hose along bulkheads instead of straight down. The 25mm hose tail lines up with common galley plumbing so you can tie into existing grey water runs without juggling odd sizes. The drain top suits a 70mm outside diameter opening so most compact marine sinks are covered without extra work. The body hanging only 35mm under the bowl helps you keep cupboard space usable. The stainless drain face holds up to regular use and salty air while the plastic elbow and hose tail keep weight down in smaller boats. The 90 degree bend and 25mm internal diameter outlet give a straight shot for standard hose clamps. The 70mm outer ring gives plenty of sealing area against the sink surface. The 35mm under-sink depth keeps the setup clear of shelves and stored gear so you can still load up the galley.
- 90 degree bent sink waste outlet
- Suits 25mm (1") internal diameter hose
- Drain outside diameter measures 70mm
- Depth under sink is 35mm
- Stainless steel drain face for durability
- Plastic outlet body and hose tail
- Compact design for tight marine lockers
- Suited to small boat and galley sinks
- Integrates with standard marine plumbing sizes
- Plug and waste supplied as a matching pair
Q: What hose size does this sink waste connect to?
It connects to hose with a 25mm internal diameter. The hose tail is moulded to suit standard 25mm marine hose so you can use common galley plumbing fittings. A 25mm I.D hose will slide over the tail without stretching. Standard hose clamps can then be used to secure the connection. This keeps spares and replacement hose straightforward on board.
Q: How far does the waste hang below the sink?
The body projects approximately 35mm under the sink. This shallow drop helps when cupboards or shelves sit close under the bowl. The 35mm depth gives space for hose and clamps while still clearing stored gear. It also helps where the benchtop is thin and lockers are shallow. Measure from the sink base to any shelf to confirm clearance.
Q: What size sink opening does the waste suit?
It suits sinks that accept a 70mm outside diameter drain body. The main drain face has a 70mm outside diameter which matches many compact marine sinks. The sealing area covers typical punched or cut drain holes in small stainless basins. Check the existing drain flange or hole size before ordering. Matching this measurement helps the seal sit correctly.
Q: What materials are used in this sink waste?
The visible drain face is stainless steel and the outlet body is plastic. Stainless steel on the top side handles regular contact with water and cleaning chemicals. The plastic body and elbow under the sink help reduce weight. This combination is common in marine plumbing where rust resistance and low weight both matter. It also keeps replacement straightforward if components are damaged.
- Suits sinks requiring 70mm drain outside diameter
- Allows 25mm (1") I.D. hose connection
- 90 degree outlet suits tight under-sink spaces
- Intended for marine sink and galley plumbing setups
- 90 degree outlet hugs bulkheads
- 25mm tail lines up with galley hose
- 35mm under-sink drop saves space
- 70mm top ring covers sink cut-outs
- Stainless and plastic combo made to last
- Outlet angle: 90 degrees
- Hose outlet internal diameter: 25mm (1")
- Drain outside diameter: 70mm
- Depth under sink: 35mm
- Construction materials: stainless steel and plastic
- Application: marine sinks and plumbing
- 90 degree sink waste body with 25mm hose outlet
- Sink plug with handle
- Integrated rubber seal
| SKU | RWB5295 |
|---|---|
| Barcode # | 8033891624279 |
| Brand | RWB Marine |
| Shipping Weight | 0.5000kg |
| Assembled Length | 0.080m |
| Assembled Height | 0.080m |
| Assembled Width | 0.080m |
More info
The RWB Marine Sink Waste & Plug 90Degree 25mm pushes water through a tight 90 degree outlet so you can run hose along bulkheads instead of straight down. The 25mm hose tail lines up with common galley plumbing so you can tie into existing grey water runs without juggling odd sizes. The drain top suits a 70mm outside diameter opening so most compact marine sinks are covered without extra work. The body hanging only 35mm under the bowl helps you keep cupboard space usable. The stainless drain face holds up to regular use and salty air while the plastic elbow and hose tail keep weight down in smaller boats. The 90 degree bend and 25mm internal diameter outlet give a straight shot for standard hose clamps. The 70mm outer ring gives plenty of sealing area against the sink surface. The 35mm under-sink depth keeps the setup clear of shelves and stored gear so you can still load up the galley.
- 90 degree bent sink waste outlet
- Suits 25mm (1") internal diameter hose
- Drain outside diameter measures 70mm
- Depth under sink is 35mm
- Stainless steel drain face for durability
- Plastic outlet body and hose tail
- Compact design for tight marine lockers
- Suited to small boat and galley sinks
- Integrates with standard marine plumbing sizes
- Plug and waste supplied as a matching pair
Q: What hose size does this sink waste connect to?
It connects to hose with a 25mm internal diameter. The hose tail is moulded to suit standard 25mm marine hose so you can use common galley plumbing fittings. A 25mm I.D hose will slide over the tail without stretching. Standard hose clamps can then be used to secure the connection. This keeps spares and replacement hose straightforward on board.
Q: How far does the waste hang below the sink?
The body projects approximately 35mm under the sink. This shallow drop helps when cupboards or shelves sit close under the bowl. The 35mm depth gives space for hose and clamps while still clearing stored gear. It also helps where the benchtop is thin and lockers are shallow. Measure from the sink base to any shelf to confirm clearance.
Q: What size sink opening does the waste suit?
It suits sinks that accept a 70mm outside diameter drain body. The main drain face has a 70mm outside diameter which matches many compact marine sinks. The sealing area covers typical punched or cut drain holes in small stainless basins. Check the existing drain flange or hole size before ordering. Matching this measurement helps the seal sit correctly.
Q: What materials are used in this sink waste?
The visible drain face is stainless steel and the outlet body is plastic. Stainless steel on the top side handles regular contact with water and cleaning chemicals. The plastic body and elbow under the sink help reduce weight. This combination is common in marine plumbing where rust resistance and low weight both matter. It also keeps replacement straightforward if components are damaged.
- Suits sinks requiring 70mm drain outside diameter
- Allows 25mm (1") I.D. hose connection
- 90 degree outlet suits tight under-sink spaces
- Intended for marine sink and galley plumbing setups
- 90 degree outlet hugs bulkheads
- 25mm tail lines up with galley hose
- 35mm under-sink drop saves space
- 70mm top ring covers sink cut-outs
- Stainless and plastic combo made to last
- Outlet angle: 90 degrees
- Hose outlet internal diameter: 25mm (1")
- Drain outside diameter: 70mm
- Depth under sink: 35mm
- Construction materials: stainless steel and plastic
- Application: marine sinks and plumbing
- 90 degree sink waste body with 25mm hose outlet
- Sink plug with handle
- Integrated rubber seal
| SKU | RWB5295 |
|---|---|
| Barcode # | 8033891624279 |
| Brand | RWB Marine |
| Shipping Weight | 0.5000kg |
| Assembled Length | 0.080m |
| Assembled Height | 0.080m |
| Assembled Width | 0.080m |
