If you run a Tube Pro 70 table leg in your van, this Camec Recess Base Plate gives it a solid home in the floor so the table stays put on corrugated tracks and sharp turns. The recessed style means the cup sits below the surface while the outer flange sits flush, so you don’t catch a boot when you move through a 600 mm wide aisle or squeeze past the dinette.
The base plate is anodised aluminium, so it shrugs off moisture and road grime better than plain steel over season-after-season trips. The cup is sized to take the Tube Pro 70 leg, giving a snug mechanical fit rather than relying on fillers. The flange carries multiple fixing points so you can spread the load across typical 12–19 mm caravan flooring and keep the whole setup tight from coast to campsite.
- Recessed base plate for Tube Pro 70 table leg
- Purpose-made for Fiamma style Tube Pro systems
- Recessed design keeps floor surface clutter-free
- Anodised aluminium construction for corrosion resistance
- Alloy body provides strong support for table loads
- Flush mounting flange with multiple screw holes
- Suitable for caravan and RV table installations
- Genuine Camec hardware for consistent fit
- Simple spare part to refresh worn bases
- Compact design suits tight interior layouts
Q: Does this base plate fit any table leg?
No, it is intended for the Tube Pro 70 table leg system. The internal cup and overall design match that specific leg size and profile, which helps reduce wobble. Using it with other leg types can leave too much play or not allow the leg to seat properly. For other legs, match the base to the brand and size marked on the hardware.
Q: Can the recessed base plate be used in both caravans and motorhomes?
Yes, it can be installed in caravans, camper vans, and motorhomes using the Tube Pro 70 leg. The key requirement is a suitable floor panel where you can cut the recess and mount the flange flat. Many builders use similar hardware across different RV bodies. Just confirm your existing leg is the Tube Pro 70 before ordering.
Q: Is the anodised aluminium suitable for outdoor or marine-style use?
The anodised aluminium construction is well suited to damp and salty environments. Anodising creates a hard surface layer that resists corrosion better than bare aluminium. That makes this base plate a good match for coastal touring and high humidity storage. Normal rinsing and occasional cleaning will help keep the finish in good shape.
Q: Do I need extra brackets or plates under the floor?
In many standard RV floors the flange and screw pattern provide enough support on their own. On thinner or softer floors some builders add backing plates underneath for extra strength. Checking the thickness and condition of your floor before cutting the recess is a smart move. If there is any flex, a backing plate can help spread the load.
- Suits Tube Pro 70 table leg systems
- Installs as a recessed base into the floor
- Mounting via perimeter screw holes on flange
- Intended for caravan and RV table leg setups
- Recessed alloy base for Tube Pro 70
- Anodised finish suits coastal touring
- Flush mount helps keep walkways clear
- Multiple screw holes for solid hold
- Handy spare part for Fiamma leg setups
- Product type: recessed base plate for Tube Pro 70 table leg
- Material: anodised aluminium construction
- Compatibility: Tube Pro 70 table leg system
- Mount type: recessed floor mounting base
- Brand: Camec
- Finish: anodised metallic
- 1 x recessed base plate for Tube Pro 70 table leg
- 1 x mounting screw set
| SKU | 007913-A |
|---|---|
| Barcode # | 007913-A |
| Brand | Camec |
| Shipping Weight | 0.5000kg |
More infoMake 4 payments of $8.00 over 8 weeks and get it now!
Calculate Shipping
If you run a Tube Pro 70 table leg in your van, this Camec Recess Base Plate gives it a solid home in the floor so the table stays put on corrugated tracks and sharp turns. The recessed style means the cup sits below the surface while the outer flange sits flush, so you don’t catch a boot when you move through a 600 mm wide aisle or squeeze past the dinette.
The base plate is anodised aluminium, so it shrugs off moisture and road grime better than plain steel over season-after-season trips. The cup is sized to take the Tube Pro 70 leg, giving a snug mechanical fit rather than relying on fillers. The flange carries multiple fixing points so you can spread the load across typical 12–19 mm caravan flooring and keep the whole setup tight from coast to campsite.
- Recessed base plate for Tube Pro 70 table leg
- Purpose-made for Fiamma style Tube Pro systems
- Recessed design keeps floor surface clutter-free
- Anodised aluminium construction for corrosion resistance
- Alloy body provides strong support for table loads
- Flush mounting flange with multiple screw holes
- Suitable for caravan and RV table installations
- Genuine Camec hardware for consistent fit
- Simple spare part to refresh worn bases
- Compact design suits tight interior layouts
Q: Does this base plate fit any table leg?
No, it is intended for the Tube Pro 70 table leg system. The internal cup and overall design match that specific leg size and profile, which helps reduce wobble. Using it with other leg types can leave too much play or not allow the leg to seat properly. For other legs, match the base to the brand and size marked on the hardware.
Q: Can the recessed base plate be used in both caravans and motorhomes?
Yes, it can be installed in caravans, camper vans, and motorhomes using the Tube Pro 70 leg. The key requirement is a suitable floor panel where you can cut the recess and mount the flange flat. Many builders use similar hardware across different RV bodies. Just confirm your existing leg is the Tube Pro 70 before ordering.
Q: Is the anodised aluminium suitable for outdoor or marine-style use?
The anodised aluminium construction is well suited to damp and salty environments. Anodising creates a hard surface layer that resists corrosion better than bare aluminium. That makes this base plate a good match for coastal touring and high humidity storage. Normal rinsing and occasional cleaning will help keep the finish in good shape.
Q: Do I need extra brackets or plates under the floor?
In many standard RV floors the flange and screw pattern provide enough support on their own. On thinner or softer floors some builders add backing plates underneath for extra strength. Checking the thickness and condition of your floor before cutting the recess is a smart move. If there is any flex, a backing plate can help spread the load.
- Suits Tube Pro 70 table leg systems
- Installs as a recessed base into the floor
- Mounting via perimeter screw holes on flange
- Intended for caravan and RV table leg setups
- Recessed alloy base for Tube Pro 70
- Anodised finish suits coastal touring
- Flush mount helps keep walkways clear
- Multiple screw holes for solid hold
- Handy spare part for Fiamma leg setups
- Product type: recessed base plate for Tube Pro 70 table leg
- Material: anodised aluminium construction
- Compatibility: Tube Pro 70 table leg system
- Mount type: recessed floor mounting base
- Brand: Camec
- Finish: anodised metallic
- 1 x recessed base plate for Tube Pro 70 table leg
- 1 x mounting screw set
| SKU | 007913-A |
|---|---|
| Barcode # | 007913-A |
| Brand | Camec |
| Shipping Weight | 0.5000kg |
