The Ceredi Snap Davit Platform Clip Assembly gives you a solid anchor point for a tender or inflatable that needs to live off the swim platform. The base runs 110mm long and 74mm wide, so it sits neatly on most small transoms without hogging deck space. The twin 7mm and 10mm mounting holes mean you can line it up with common bolt patterns and keep the drill work simple. The body uses a shaped housing around a solid metal loop so the load from the davit arm spreads cleanly across the 110mm base. The 74mm plate width keeps the clip steady when the boat noses into chop or wash. The pre sized 7mm and 10mm holes match standard marine fasteners that handle constant spray and movement. The compact footprint means you keep room free for other deck gear while the davit setup does its job.
- Ceredi Snap Davit Platform Clip Assembly
- Part number 39196 for easy reference
- Base length measures 110mm overall
- Mounting plate width is 74mm
- Twin mounting hole diameters 7mm and 10mm
- Suits snap davit setups for inflatables and tenders
- Compact footprint fits small swim platforms
- Pre drilled holes simplify alignment and install
- Solid clip loop for repeat attachment cycles
- Marine hardware suited to deck and transom use
Q: Can this clip assembly be mounted to either timber or fibreglass platforms?
Yes, it can be mounted to both. The base uses standard 7mm and 10mm mounting holes that accept common marine bolts. That means you can bolt through a timber duckboard or a fibreglass swim platform as long as you use suitable backing washers or plates. Always follow good boatbuilding practice for sealing and reinforcing fixings.
Q: Do I need a matching Ceredi snap davit head for this assembly?
Yes, it should be paired with compatible snap davit hardware. This clip assembly forms one half of a snap davit system and is intended to work with a corresponding davit head on the inflatable. Using matching gear keeps the latch action clean and reduces wear. Mixing brands can affect how the clip engages and may shorten service life.
Q: Can one platform clip assembly support an entire inflatable dinghy?
No, you normally need a pair. Standard snap davit systems use two platform clips to support the tender at two spaced points. Running only one mount can twist the inflatable and overload the hardware. Fitting a pair at the recommended spacing shares the load and makes launch and retrieval smoother.
Q: Are the mounting bolts or backing plates included with this assembly?
No, the fasteners are not included. The assembly ships as the clip unit only so you can choose bolt lengths and types that match your transom or platform thickness. Selecting your own hardware lets you match existing stainless grade and head style. Always use quality marine fasteners for long term use in saltwater.
Suitable for use as a snap davit platform clip assembly on inflatable boat setups where a 110mm long and 74mm wide mounting base with 7mm and 10mm mounting holes is compatible with the existing platform or transom hardware layout.
- 110mm base fits most small platforms
- 74mm wide plate for solid footing
- Twin 7mm and 10mm fixing options
- Simple clip point for tender davits
- Built tough for regular marine use
- Part number: 39196
- Length: 110mm
- Width: 74mm
- Mounting hole diameters: 7mm and 10mm
- Application: Snap davit platform clip assembly for inflatable boat setups
Ceredi Snap Davit Platform Clip Assembly x 1
| SKU | 39196 |
|---|---|
| Barcode # | 9330420121308 |
| Brand | Ceredi |
| Shipping Weight | 1.0000kg |
More info
The Ceredi Snap Davit Platform Clip Assembly gives you a solid anchor point for a tender or inflatable that needs to live off the swim platform. The base runs 110mm long and 74mm wide, so it sits neatly on most small transoms without hogging deck space. The twin 7mm and 10mm mounting holes mean you can line it up with common bolt patterns and keep the drill work simple. The body uses a shaped housing around a solid metal loop so the load from the davit arm spreads cleanly across the 110mm base. The 74mm plate width keeps the clip steady when the boat noses into chop or wash. The pre sized 7mm and 10mm holes match standard marine fasteners that handle constant spray and movement. The compact footprint means you keep room free for other deck gear while the davit setup does its job.
- Ceredi Snap Davit Platform Clip Assembly
- Part number 39196 for easy reference
- Base length measures 110mm overall
- Mounting plate width is 74mm
- Twin mounting hole diameters 7mm and 10mm
- Suits snap davit setups for inflatables and tenders
- Compact footprint fits small swim platforms
- Pre drilled holes simplify alignment and install
- Solid clip loop for repeat attachment cycles
- Marine hardware suited to deck and transom use
Q: Can this clip assembly be mounted to either timber or fibreglass platforms?
Yes, it can be mounted to both. The base uses standard 7mm and 10mm mounting holes that accept common marine bolts. That means you can bolt through a timber duckboard or a fibreglass swim platform as long as you use suitable backing washers or plates. Always follow good boatbuilding practice for sealing and reinforcing fixings.
Q: Do I need a matching Ceredi snap davit head for this assembly?
Yes, it should be paired with compatible snap davit hardware. This clip assembly forms one half of a snap davit system and is intended to work with a corresponding davit head on the inflatable. Using matching gear keeps the latch action clean and reduces wear. Mixing brands can affect how the clip engages and may shorten service life.
Q: Can one platform clip assembly support an entire inflatable dinghy?
No, you normally need a pair. Standard snap davit systems use two platform clips to support the tender at two spaced points. Running only one mount can twist the inflatable and overload the hardware. Fitting a pair at the recommended spacing shares the load and makes launch and retrieval smoother.
Q: Are the mounting bolts or backing plates included with this assembly?
No, the fasteners are not included. The assembly ships as the clip unit only so you can choose bolt lengths and types that match your transom or platform thickness. Selecting your own hardware lets you match existing stainless grade and head style. Always use quality marine fasteners for long term use in saltwater.
Suitable for use as a snap davit platform clip assembly on inflatable boat setups where a 110mm long and 74mm wide mounting base with 7mm and 10mm mounting holes is compatible with the existing platform or transom hardware layout.
- 110mm base fits most small platforms
- 74mm wide plate for solid footing
- Twin 7mm and 10mm fixing options
- Simple clip point for tender davits
- Built tough for regular marine use
- Part number: 39196
- Length: 110mm
- Width: 74mm
- Mounting hole diameters: 7mm and 10mm
- Application: Snap davit platform clip assembly for inflatable boat setups
Ceredi Snap Davit Platform Clip Assembly x 1
| SKU | 39196 |
|---|---|
| Barcode # | 9330420121308 |
| Brand | Ceredi |
| Shipping Weight | 1.0000kg |
