This Sam Allen 90 degree sink waste with 25 mm plug suits tight galley or cabin sinks where there is not much room under the bowl. The elbow turns the outlet sideways so you can run hose across the back of a cupboard instead of straight down. The matched 25 mm plug and waste keep dish water in the sink while you scrub and rinse. The setup works well on smaller boats and campers with compact benchtops. The waste body uses a lightweight plastic construction that keeps weight down in smaller rigs. The outlet tail has moulded barbs to grip the drain hose without needing heavy clamps. The plug fits a 25 mm seat so it drops in cleanly every time. The simple design has no moving parts so there is less to fail when you are a long way from spare parts. It is a smart buy for basic marine and touring plumbing.
- Part number 50414 sink waste assembly
- Includes matching waste body and plug
- Plug diameter specified as 1 inch (25 mm)
- 90 degree outlet for tight cabinet spaces
- Suits marine and small galley sink installations
- Lightweight plastic construction for low system weight
- Barbed outlet tail to accept compatible drain hose
- Intended for grey water use in sinks
- Simple design with no moving mechanisms
- Supplied as waste plus plug set for direct replacement
Q: Can this 90 degree sink waste be used in a caravan as well as a boat?
Yes, it can be used in both. The lightweight plastic body and compact 90 degree outlet work in any small sink with a 25 mm plug seat. Many caravan and camper sinks share similar drain sizes with small marine galleys. As long as the sink has a compatible hole and the hose matches the barbed tail, the waste will function the same way on land or water.
Q: What size sink hole does the 25 mm plug suit?
It suits sinks that take a 25 mm plug. The plug diameter is listed as 1 inch which equals 25 mm. That measurement refers to the sealing diameter where the plug sits in the waste fitting. If your current plug is marked 1 inch or measures close to 25 mm across the sealing face, this waste and plug set will generally be compatible.
Q: Do I need any special tools to fit this waste?
Usually only basic hand tools are needed. Most installs involve removing the old waste collar, cleaning the sink hole and tightening the new fitting with hand pressure or a simple spanner. Hose connection is normally done by sliding the hose over the barbed tail and securing it with a clamp. Always check access behind the sink before starting the job.
Q: Is this waste suitable for grey water only?
Yes, it is intended for grey water. The unit is made for standard sink use where the water contains detergent, food residue and general washing runoff. It is not intended for black water or chemical toilet systems. Using it within a normal galley or caravan sink setup helps keep wear within what the materials are designed to handle.
- Suits sink outlets designed for 1 inch (25 mm) plugs
- Suitable for marine sink and galley plumbing setups
- 90 degree outlet suits hose routing below or behind sink
- Connects to compatible waste hose sized for the barbed tail
- 90 degree bend for tight installs
- 25 mm plug for compact bowls
- Light plastic gear for small rigs
- Barbed tail to grip hose well
- Straightforward waste and plug setup
- Part number: 50414
- Plug diameter: 1 inch (25 mm)
- Waste and plug supplied as a set
- Configuration: 90 degree sink waste outlet
- Application: marine sinks and plumbing systems
- 90 degree sink waste body
- 1 inch (25 mm) sink plug
| SKU | 50414 |
|---|---|
| Barcode # | 9330420012347 |
| Brand | Sam Allen |
| Shipping Weight | 0.4000kg |
More info
This Sam Allen 90 degree sink waste with 25 mm plug suits tight galley or cabin sinks where there is not much room under the bowl. The elbow turns the outlet sideways so you can run hose across the back of a cupboard instead of straight down. The matched 25 mm plug and waste keep dish water in the sink while you scrub and rinse. The setup works well on smaller boats and campers with compact benchtops. The waste body uses a lightweight plastic construction that keeps weight down in smaller rigs. The outlet tail has moulded barbs to grip the drain hose without needing heavy clamps. The plug fits a 25 mm seat so it drops in cleanly every time. The simple design has no moving parts so there is less to fail when you are a long way from spare parts. It is a smart buy for basic marine and touring plumbing.
- Part number 50414 sink waste assembly
- Includes matching waste body and plug
- Plug diameter specified as 1 inch (25 mm)
- 90 degree outlet for tight cabinet spaces
- Suits marine and small galley sink installations
- Lightweight plastic construction for low system weight
- Barbed outlet tail to accept compatible drain hose
- Intended for grey water use in sinks
- Simple design with no moving mechanisms
- Supplied as waste plus plug set for direct replacement
Q: Can this 90 degree sink waste be used in a caravan as well as a boat?
Yes, it can be used in both. The lightweight plastic body and compact 90 degree outlet work in any small sink with a 25 mm plug seat. Many caravan and camper sinks share similar drain sizes with small marine galleys. As long as the sink has a compatible hole and the hose matches the barbed tail, the waste will function the same way on land or water.
Q: What size sink hole does the 25 mm plug suit?
It suits sinks that take a 25 mm plug. The plug diameter is listed as 1 inch which equals 25 mm. That measurement refers to the sealing diameter where the plug sits in the waste fitting. If your current plug is marked 1 inch or measures close to 25 mm across the sealing face, this waste and plug set will generally be compatible.
Q: Do I need any special tools to fit this waste?
Usually only basic hand tools are needed. Most installs involve removing the old waste collar, cleaning the sink hole and tightening the new fitting with hand pressure or a simple spanner. Hose connection is normally done by sliding the hose over the barbed tail and securing it with a clamp. Always check access behind the sink before starting the job.
Q: Is this waste suitable for grey water only?
Yes, it is intended for grey water. The unit is made for standard sink use where the water contains detergent, food residue and general washing runoff. It is not intended for black water or chemical toilet systems. Using it within a normal galley or caravan sink setup helps keep wear within what the materials are designed to handle.
- Suits sink outlets designed for 1 inch (25 mm) plugs
- Suitable for marine sink and galley plumbing setups
- 90 degree outlet suits hose routing below or behind sink
- Connects to compatible waste hose sized for the barbed tail
- 90 degree bend for tight installs
- 25 mm plug for compact bowls
- Light plastic gear for small rigs
- Barbed tail to grip hose well
- Straightforward waste and plug setup
- Part number: 50414
- Plug diameter: 1 inch (25 mm)
- Waste and plug supplied as a set
- Configuration: 90 degree sink waste outlet
- Application: marine sinks and plumbing systems
- 90 degree sink waste body
- 1 inch (25 mm) sink plug
| SKU | 50414 |
|---|---|
| Barcode # | 9330420012347 |
| Brand | Sam Allen |
| Shipping Weight | 0.4000kg |
